US HRC: Prices jump on higher mill offers
US hot-rolled coil (HRC) prices jumped this week as mills aimed for higher prices in January amid increasingly limited supply.
The Argus weekly domestic US HRC index rose by $65/short ton (st) to $820/st ex-works Midwest this week, the largest increase Argus assessment has ever recorded. Lead times were flat at 8-9 weeks. The spot price is the highest since November 2018, and is up by 82pc since a yearly low of $450/st recorded in mid-August.
One large service center bought 10,000st of HRC from a non-Midwest electric arc furnace (EAF) minimill for $840/st for January delivery. The buyer said options were slim, with many mills essentially booked for January and holding off opening up their February books to secure higher prices.
Integrated steelmakers ArcelorMittal and US Steel pushed prices as high as $850/st for January, according to market participants. With little to no spot availability, steel buyers have wondered whether the higher offers mean anything if there is no supply available.
Some manufacturers may be impacted in December because of a lack of steel, said one market participant. Many are still waiting for months of backorders, delayed by steelmakers because of the rush of buying over the last three months.
The ferrous scrap trade is expected to begin this week, with #1 busheling delivered US Midwest expected to increase by as much as $50/gross ton (gt), in large part to keep up with gains in finished steel prices.
The spread between #1 busheling scrap delivered US Midwest mills and HRC selling prices was $556.61/st, 13pc higher than the spread of $491.61/st from the week before and 59pc higher than the $349.46/st recorded a year ago.
The domestic US cold-rolled coil (CRC) assessment rose by $60/st to $970/st ex-works, and the hot-dipped galvanized (HDG) coil assessment increased by $55/st to $970/st. Lead times for CRC and HDG expanded to 10-12 weeks from 12 weeks.
HRC import prices into Houston increased by $60/st to $800/st ddp on continued increases in foreign pricing.
The CME HRC futures market mostly posted gains in the last week, with January futures jumping up by $21/st to $841/st and February prices increasing by $16/st to $821/st. March prices slipped by $1/st to $799/st, while April prices rose by $13/st to $770/st. May futures prices rose by $6/st to $746/st, while June prices increased by $3/st to $738/st.
Plate
The Argus weekly domestic US plate assessment rose by $63.25/st to $770/st on the week on the back of a price increase from Nucor as plate mills attempt to keep pace with HRC increases. Lead times broadened to 6-8 weeks from 8 weeks.
Related news posts
US Fed cuts rate by half point, signals more to come
US Fed cuts rate by half point, signals more to come
Houston, 18 September (Argus) — The US Federal Reserve cut its target interest rate by 50 basis points today, the first rate cut since 2020, with officials signaling they expect to make another half point worth of cuts by the end of 2024. The Fed's Federal Open Market Committee (FOMC) lowered the federal funds rate to 4.75-5pc from the prior range of 5.25-5.5pc, which was a two-decade high. The Fed had kept the target rate unchanged since July 2023 after hiking it for more than a year in the most aggressive increase campaign in four decades to quash inflation, which peaked at 9.1pc in mid-2022. "The committee has gained greater confidence that inflation is moving sustainably toward 2pc and judges that the risks to achieving its employment and inflation goals are roughly in balance," the FOMC said in its statement after the two-day meeting. "Job gains have slowed, and the unemployment rate has moved up but remains low." The Fed board and policymakers, in their latest economic projections, expect the target rate range will end 2024 near a midpoint of 4.4pc compared with an end of year midpoint of 5.1pc projected in June, which implies further cuts amounting to 50 basis points by the end of 2024. By Bob Willis Send comments and request more information at feedback@argusmedia.com Copyright © 2024. Argus Media group . All rights reserved.
Japan's Tokyo Steel cuts sales prices on weak demand
Japan's Tokyo Steel cuts sales prices on weak demand
Shanghai, 18 September (Argus) — Japan's steel manufacturing firm Tokyo Steel said it will cut domestic steel product prices for October, marking the first full-scale price cut in over four years. The decision was driven by sluggish domestic demand and increased competition from cheaper imported steel products. Tokyo Steel will reduce prices across all product lines starting October, with steel coils and plates dropping by ¥15,000/t, shaped beams by ¥12,000/t, and tubes and deformed bars by ¥10,000/t. The company had maintained stable domestic steel prices for an extended period on the back of the steadier domestic demand and market conditions compared to the more volatile overseas market. The last price cut for deformed bars was in July 2023. Steel sales in Japan were weak during the third quarter, impacted by rising procurement costs for materials, a shortage of construction capacity, and an influx of cheaper steel products from China in the seaborne market, market participants said. A decline in profitability pushed Japanese mills to cut production costs. From 11 July to 14 September, domestic scrap prices at Tokyo Steel's Utsunomiya plant dropped by ¥12,500/t, or 23.8pc. Market sentiment in Japan remains bearish due to economic uncertainty and the strengthening of the Japanese yen. The upcoming adjustments in US monetary policy could add further volatility to exchange rates. "We may see more corrections in the Japanese domestic market," a trade source said. Send comments and request more information at feedback@argusmedia.com Copyright © 2024. Argus Media group . All rights reserved.
July EU HRC imports show 175,000t pullback
July EU HRC imports show 175,000t pullback
London, 17 September (Argus) — EU hot-rolled coil (HRC) imports surpassed 1.5mn t in July — a record high — as importers for the first time faced a cap to the ‘other countries' safeguard quota, which led some to purchase back-up material from other sources. More importantly, official figures show that around 175,000t were pulled back from customs clearing, likely all in Italy, after the initial quota numbers were made available in early July from Egypt, Vietnam, Japan and Taiwan. This leftover amount will likely all be custom-cleared in October, in addition to material that has arrived since July, as market participants expect importers to clear all of their HRC to avoid the risk of retroactive duties, potentially applicable from December. Imports from Taiwan, India, Turkey and Japan in July all surpassed the 200,000t mark each, with total imports from those four origins close to 900,000t, a sharp year-on-year increase. Vietnam saw volumes drop ( see table ), while South Korean imports fell by 75pc on the year to 40,379t and Serbian imports were down by 10pc to 37,437t. Hot-dipped galvanised (HDG) imports were at a record high, topping 750,000t in July, with nearly 30pc of the total from Vietnam. There has been concern in the market that the EU might start an investigation on Vietnamese HDG, as volumes have been on the increase, while suppliers are regularly the lowest-priced in the market. Plate imports were also at a record high, as EU producers are preparing to file for an investigation on some origins. Meanwhile, the increase in imports and the drop in EU demand has led producers to seek export outlets, with EU HRC exports rising on the year and on the month in July to nearly 230,000t, with the bulk going to the UK, US and Turkey. Downstream product exports also increased. By Lora Stoyanova and Colin Richardson July EU HRC imports t July y-o-y ±% Taiwan 227,892.8 8.2 India 225,558.6 134.8 Turkey 223,185.9 255.2 Japan 210,842.9 6.5 Egypt 158,625.7 31.9 Vietnam 144,202.0 -59.5 Ukraine 101,721.2 118.5 Australia 51,784.0 104.4 Saudi Arabia 40,594.8 -36.4 Total 1,565,744.2 9.1 — GTT Send comments and request more information at feedback@argusmedia.com Copyright © 2024. Argus Media group . All rights reserved.
US to impose 25pc tariffs on Chinese critical minerals
US to impose 25pc tariffs on Chinese critical minerals
Houston, 13 September (Argus) — The US plans to impose 25pc tariffs on Chinese minerals including indium, tantalum, chromium, cobalt and tungsten, citing China's efforts to dominate global supply chains, according to the office of the US Trade Representative (USTR). The USTR determined not to exclude any critical minerals from the proposed Section 301 tariffs. The USTR said the concentration of mining and refining capacity of these minerals in China, as well as China's effort to dominate the global supply chains for these minerals, endangers US national security and clean energy goals. The Section 301 tariffs on indium, tantalum, chromium, cobalt, and tungsten will go into effect on 27 September. Tariffs on natural graphite and permanent magnets will go into effect on 1 January 2026. China is the leading producer and exporter of indium, producing an estimated 650t in 2023, about 66pc of the global total, according to the US Geological Survey (USGS). The US imported 219 metric tonnes (t) of unwrought indium in 2023, including 10t from China. So far in 2024 the country has imported 148t, of which 45t originated in China, according to data from the US Commerce Department. Indium is primarily used globally for its electric conductivity in a variety of screens including liquid crystal displays (LCDs) as well as fiber-optic cables and other technical components. US consumption is more focused around solders and specialty alloys. The US imports more tantalum powders, alloys, and metals from China than any other country. The US imported 321t of unwrought tantalum in 2023, including 132t from China and has imported 269t between January and July 2024, including 178t from China. Tantalum is primarily used in high-temperature alloys and capacitors. Although China accounted for only 3.3pc — 79t — of global 2023 mine production, the USGS estimated the country had a world-leading 240,000t of tantalum reserves. Chromium is primarily used in stainless and heat-resistant steels. China is the world's largest producer of ferrochromium and stainless steel. The US imported 103,034t of chromium ores and concentrates in 2023, including just 10t from China. Still, the US did import 9,302t of unwrought chrome metal from China so far in 2024, which accounted for 74pc of total volumes, and US reliance on China for the metal has increased since sanctions forced Russian supplies off the table. Although China does not mine a significant amount of cobalt, it is the world's leading cobalt refiner and consumer. The US imported 18t of cobalt ores and concentrates in 2023, including 11t from China, and imported 11t between January and July 2024, including 6t from China. The US imported 1.6mn contained kilograms (ckg) of tungsten carbides in 2023, including 906,000ckg from China and imported 1mn ckg between January and July 2024, including 491,000ckg from China. Tungsten is primarily used in carbide parts for construction, metalworking, mining, and drilling applications. Tungsten is also used in specialty steel fabrication as well as in electrodes, filaments, and wires for various electrical and electronic products. By Cole Sullivan Critical Mineral Tariffs metric tonnes, t HTS Code Resource Name Imports from China, 2023 Imports from China, 2024 through July 2605.00.00 Cobalt ores and concentrates 11 6 2610.00.00 Chromium ores and concentrates 10 52 2611.00.60 Tungsten concentrates 139 46 2825.90.30 Tungsten oxides 212 19 2841.80.00 Tungstates (wolframates) 0 0 2849.90.30 Tungsten Carbide* 906,375 491,371 8101.10.00 Tungsten, powders 0 0 8103.20.00 Tantalum, unwrought 132 178 8112.92.30 Indium, unwrought; powders 10 45 Source: US Commerce Department *unit of measure is kilograms contained Send comments and request more information at feedback@argusmedia.com Copyright © 2024. Argus Media group . All rights reserved.
Business intelligence reports
Get concise, trustworthy and unbiased analysis of the latest trends and developments in oil and energy markets. These reports are specially created for decision makers who don’t have time to track markets day-by-day, minute-by-minute.
Learn more